The shell
Wall thickness, corner radius and face fabric decide how much impact a case absorbs. We press 5 mm EVA from 75D foam, faced in 1680D, 600D or PU.
We are an EVA hard case factory in Shijie Town, Dongguan: 10+ years of compression moulding, 120+ staff, 150,000 pcs of monthly capacity and a library of 300+ existing moulds. Mould drawing, pressing, stitching, lining and packing all happen in one building, so a project never waits on a third party. MOQ is 300 pcs per style.
A moulded shell begins as a flat sheet: 5 mm EVA foam laminated to 1680D nylon, 600D polyester or PU leather, cut to a flat pattern, then pressed over an aluminium mould until it holds the tool shape. The shell stays rigid after cooling, so the case carries a device instead of resting on it. We draw and cut every mould in our own tool room.
A sewn nylon case is a bag with a soft wall: it folds, it sags, and it passes impact straight to the contents. A moulded EVA shell is a rigid 5 mm wall with a controlled radius at every corner, so a 1.2 m drop on six faces spreads the load across the whole panel. That is why drone, VR and medical buyers specify moulded shells and ask for ISTA 3A test reports.
Three decisions fix cost and protection before a case is pressed. Change one later and the tooling changes with it.
Wall thickness, corner radius and face fabric decide how much impact a case absorbs. We press 5 mm EVA from 75D foam, faced in 1680D, 600D or PU.
Die-cut foam holds the device; a loose insert lets it move. We cut EVA or PU to the product outline and test-fit your sample before finishing.
Zipper, lining, handle and logo decide how a case reads on a shelf. We fit YKK or waterproof zippers, velvet or jersey lining and webbing handles.
The first shell out of a new mould is a first article, not a production unit. We measure wall thickness at nine points, check the zipper gap around the full perimeter, and drop the case at 1.2 m on six faces with a weighted dummy inside. If one corner deforms, the mould is re-cut before the run starts. The same check runs again on every reorder.
Bulk runs carry three checks: an inline inspection every 50 pcs, a full measurement pass against the approved spec, and an AQL 2.5 final inspection with photos of the carton, the label and the shell surface. Zippers are cycle-tested to 5,000 open-and-close cycles. You receive the report, the measurement sheet, the defect log and retained samples before the balance is due.
Four formats that run through the plant monthly. Each can be re-pressed in another face fabric, lining and insert at 300 pcs.
5 mm shell, die-cut foam, shoulder strap
Velvet lining, moulded controller bay
600D face, mesh pocket, webbing loop
PU leather face, pick-and-pluck foam
Most projects run 7–10 days to sample and 20–30 days to bulk. A new mould moves the sampling date, not the production window.
A 3D file, a sketch or the physical product works. Tell us the drop standard and the target retail price and we will say whether a 5 mm shell is the right wall.
We check your product against 300+ existing moulds first. If one fits, sampling takes 7–10 days; a new mould takes 15–20 days including the first article.
You receive a finished case with the final lining, zipper and insert, a measurement sheet, a photo set from six angles and any deviation noted in writing.
20–30 days after approval: moulding, trimming, lining, zipper fitting, insert assembly and packing, with an inline inspection every 50 pcs and a daily output report.
AQL 2.5 final inspection and a photo report, then cartons marked to your instruction, a packing list signed off and loading FOB Shenzhen or Yantian, CIF or DDP.
The range we press most often. Anything outside it is a tooling conversation, not a refusal.
FOB Shenzhen at 1,000 pcs unless stated: 5 mm shell, 1680D face, velvet lining and a die-cut insert. Tooling is quoted separately and credited on 2,000+ pcs.
US$2.60 / pc
Watch, jewellery and thermometer formats, FOB at 1,000 pcs.
US$4.20 / pc
BP monitor, action camera and headphone formats, FOB at 1,000 pcs.
US$9.80 / pc
Drone fly-more, VR headset and keyboard formats, FOB at 2,000 pcs.
Tell us the device, drop standard and quantity. We will say whether a stock mould fits or a new one is needed, and price both.