Our EVA Hard Case Factory in Dongguan

Plant overview

One building, every step of a moulded case

Four walls in Shijie Town hold the whole sequence: tooling, pressing, foam cutting, stitching, logo and packing. Nothing is subcontracted between those steps.

4,200 m²

One floor in Jizhou 3rd Industrial Zone, Shijie Town: tool room, moulding, foam cutting, stitching, logo and packing in the same building.

6 stitching lines

52 machinists, each line set up for zippers, webbing handles and shoulder-strap anchors on moulded shells.

150,000 pcs / month

Output at full run across eight case families, with 140,000 pcs already scheduled against named programmes.

Machines

The equipment list, item by item

The plant is built around six compression presses and four die-cutting presses, which sets both the shell size and the insert size we can quote. Tool masters are cut on our own CNC routers, so a cavity change does not wait on an outside supplier. We hold 300+ moulds on file.

Compression moulding
6 presses at 160–180 °C, forming 5 mm EVA sheet over aluminium tools.
Die-cutting
4 presses up to 1,200 × 800 mm, cutting foam cavities to ±2 mm.
CNC routing
2 routers producing tool masters and plywood cavity patterns.
Stitching
6 lines, lockstitch and double-needle, YKK and waterproof zippers.
Logo stations
1 heat-transfer press and 1 embossing station, both in-house.
Drop-test rig
1 rig, 1.2 m onto concrete on six faces, run before a shell is released.
Aluminium mould on a compression press at the Dongguan factory
Process

Six steps from drawing to carton

Each step has a sign-off, and the next step does not start until it is signed.

01

Drawing

Your device outline, logo files and packing list become a 2D drawing. Wall thickness, corner radius and insert layout are fixed before tooling is quoted.

02

Mould

A new aluminium tool is cut on our CNC routers, so sampling on a fresh drawing runs 15–20 days. On a mould already on file, sampling takes 7–10 days.

03

Laminate

5 mm EVA sheet is laminated to 1680D nylon, 600D polyester or PU leather, then cut to blank size on the die-cutting presses.

04

Press

The blank is formed over the tool at 160–180 °C. Walls and corners are measured against the drawing at ±1.5 mm before the run continues.

05

Insert and logo

Die-cut EVA, pick-and-pluck or a thermoformed tray is fitted at ±2 mm, then the logo goes on: heat transfer, embossing, metal plate or rubber patch.

06

Inspect and pack

1.2 m drop on six faces, 5,000-cycle zipper, 30 kg handle pull, then AQL 2.5 final inspection, photo report and retail packing.

Inspector measuring a moulded EVA shell against its drawing
Quality control

Five tests stand between a shell and a carton

Testing runs next to the presses rather than in a separate building, so a failure reaches the tool room the same shift. Every new shell is dropped and measured before the first bulk run; every reorder repeats the same gates. REACH and RoHS test reports on the shell, lining and foam are available on request.

Drop test
1.2 m onto concrete on six faces, with the device or a matched dummy load inside.
Zipper cycling
5,000 open-and-close cycles on the fitted zipper, then a pull-strength check.
Handle pull
30 kg static pull on the webbing handle and on both shoulder-strap anchors.
Final inspection
AQL 2.5 across the carton, with a photo report before the box is sealed.
Tolerances
±1.5 mm on the moulded shell, ±2 mm on die-cut insert cavities.
Capacity

Monthly output by case family

At full run the plant ships 150,000 pcs a month. The eight families below absorb 140,000 pcs of that; the balance stays free for new tooling trials and peak reorders.

Drone cases
22,000 pcs / month
VR headset cases
14,000 pcs / month
Camera cases
18,000 pcs / month
Tool and instrument cases
26,000 pcs / month
Medical device cases
12,000 pcs / month
Watch and jewellery cases
16,000 pcs / month
Electronics cases
24,000 pcs / month
Home and outdoor cases
8,000 pcs / month
The floor

What a buyer sees on a walkthrough

Stitching line closing zippers on moulded EVA hard cases

Stitching line

6 lines, 52 machinists
Moulded drone fly-more case with a die-cut insert

Drone cases

22,000 pcs / month
Moulded VR headset case with velvet lining

VR cases

14,000 pcs / month
Moulded tool case with a shadow-board insert

Tool cases

26,000 pcs / month

Book a factory visit or a video walkthrough

Come to Shijie Town and press a test shell yourself, or take a live video walkthrough of the moulding, cutting and stitching rooms.