Custom Foam Inserts: Die-Cut, Pick-and-Pluck and EVA Trays

A foam insert turns a moulded shell into a case that holds one device, in one orientation, with the lid closing on the same tolerance every time. We cut four insert types in Shijie Town: die-cut EVA, pick-and-pluck foam, thermoformed EVA trays and moulded EVA shells. This page compares what each costs, how precise it is, and which quantity justifies the tooling.

Insert engineering

Insert design is a tolerance decision, not a foam purchase

An insert starts with the device, not the case. We ask for the unit itself, a 1:1 mock-up, or a STEP file with the ports, buttons and antenna zones marked. From that we set the cavity, the finger pull and the lid clearance. Die-cut EVA holds ±2 mm on the outline, so a phone-sized cavity is easy and a 90 mm lens barrel needs a test cut before bulk.

Density decides how the insert behaves in a drop test. A 25D EVA at 20 mm cushions the device and absorbs a 1.2 m drop, but it sags under a 2 kg tool. A 38D EVA at 15 mm stays flat and holds a shaped cavity without a backing board. Most cases we build use 25D on the lid and 38D in the base.

  • Die-cut outline tolerance ±2 mm, drawn on the cut file
  • Foam density 25D for cushioning, 38D for structure
  • Insert thickness 10–30 mm, cut to the shell depth
  • Cut file: DXF, AI or STEP, plus a device mock-up
Send your device drawing
Die-cut EVA foam inserts being cut on a press
The three variables

Density, thickness and tolerance decide whether the device fits

Change one and the unit moves inside the shell. We fix all three before a die is made.

Foam density

25D EVA compresses around a device and absorbs shock; 38D EVA holds a shaped cavity flat under a 2 kg tool. Both are laminated to 1680D nylon or jersey in-house.

Thickness

Inserts run 10–30 mm. A 10 mm sheet lines a lid, 20 mm cradles a camera body, 30 mm fills a tool case. Shell depth, not foam size, sets the limit.

Tolerance

Die-cut EVA holds ±2 mm on the cavity edge. Pick-and-pluck holds ±5 mm because it releases in 10 mm squares. Give us the device tolerance and we pick the process.

Proof before production

We cut a first article and load the real device

Every insert is checked against the device, not the drawing. We cut a first article, load the actual unit, close the shell and shake it. A 90 mm lens barrel should not shift; a 12 mm cable channel should still pass a plug. Any cavity outside ±2 mm goes back to the CAD table before the die is cut and the drawing is reissued.

Foam is tested as an assembly, because a case only protects as a stack. We drop 1.2 m on six faces with the device loaded, compress a 20 mm insert to 50% of its height for 1,000 cycles, and measure how much it recovers. An insert that loses more than 3 mm is re-cut in 38D. Density and phthalate test reports are available on request.

  • First-article check with the real device loaded
  • 1.2 m drop test on six faces, device inside
  • Compression set under 3 mm after 1,000 cycles
  • Test reports on foam density and phthalates on request
Ask for a test cut
Foam insert being checked against a device before production
Insert types

Four insert builds we cut every week

Each photo is a production insert, not a render. Every one can be re-cut for your device.

Process

From device outline to shipped insert in five steps

Most insert projects take 20–40 days end to end, depending on whether a die has to be made.

01

Send the device or a file

Ship the unit, or send a STEP file with ports and buttons marked. A photo plus three measurements is enough for an indicative quote in 2 working days.

02

Choose the process

We match the device, the quantity and the budget to one of the four insert types, then confirm the cavity drawing within 2 working days.

03

Approve the first article

We cut one insert, load the device and send photos with the cavity measurements. You approve the fit before the die is ordered or the run goes ahead.

04

Cut and assemble

Die-cut and pick-and-pluck inserts run at 500–1,000 pcs a day, laminated to the shell lining with hot-melt film and checked at every 20th piece against the drawing.

05

Pack and ship

Inserts ship flat or pre-fitted in the case, polybagged at 25 pcs per carton with a packing list, FOB Shenzhen or Yantian, CIF or DDP.

Specs

The four insert types, side by side

Tooling, tolerance and minimum run separate these four. Each can be laminated to velvet, jersey or 5 mm EVA.

Die-cut EVA
Steel-rule die; ±2 mm outline; 500 pcs and up; 10–30 mm; 25D or 38D
Pick-and-pluck
No tool; ±5 mm in 10 mm squares; from 100 pcs; 30–50 mm blocks
Thermoformed tray
Aluminium former; ±1 mm; 500 pcs and up; 0.8–1.5 mm EVA sheet
Moulded EVA shell
Compression mould; ±1 mm; 2,000 pcs and up; 5 mm 75D EVA
Insert lining
Velvet, jersey, 2 mm EVA or 1680D nylon, bonded with hot-melt film
Case shell
5 mm 75D EVA, hot-pressed to 1680D nylon, PU leather or jersey
Cavity data
STEP, DXF or AI cut file, or a 1:1 device mock-up we digitise
Minimum and lead time
100 pcs pick-and-pluck; 500 pcs for a new die; bulk 20–30 days
Choosing

What each insert type is for

Pick by quantity first, then by how precisely the device seats in the cavity.

Die-cut EVA

A steel-rule die cuts the cavity in one stroke, so every piece matches to ±2 mm. The tool is a one-off, so the process makes sense above 500 pcs. Clean edges, no grid.

Pick-and-pluck foam

Pre-cut foam releases in 10 mm squares, so the cavity is shaped by hand. No tool, so a 100 pcs run is possible. Edges are stepped and the fit is ±5 mm.

Thermoformed EVA tray

A heated 1 mm EVA sheet is pulled over a former, giving thin walls and a repeatable drop-in fit. The choice when a device has to seat the same way every time.

Moulded EVA shell

The 5 mm case wall is compressed around a shaped cavity, so there is no separate insert. The strongest build, needs a steel mould, and pays back at 2,000 pcs.

Indicative pricing

Case plus insert, three volumes

FOB Shenzhen, 1,000 pcs unless the line states otherwise, insert fitted and shell lined. New dies and moulds are quoted separately.

Pick-and-pluck

US$2.90 / pc

100–499 pcs, medium stock shell, 30 mm pluck foam, your logo on the lid.

  • 100 pcs minimum
  • Stock mould from the 300+ library
  • 30 mm pick-and-pluck insert
  • Heat-transfer logo, 1 colour

Moulded shell

US$8.40 / pc

2,000+ pcs, new moulded EVA shell with the cavity formed into the wall.

  • 2,000 pcs
  • New mould US$600–1,400, credited against the run
  • Shaped cavity, no separate insert
  • Custom lining and zipper puller

Foam insert questions

Five questions buyers ask before sending a device outline.

Which insert type should I choose?
Match the quantity first. Under 500 pcs, pick-and-pluck foam avoids a die. Above 500 pcs a die-cut 38D insert gives ±2 mm repeatability. At 2,000 pcs a moulded EVA shell puts the cavity in the wall itself.
How precise is a die-cut insert?
±2 mm on the cavity outline. We confirm the fit on a first article loaded with the real device before the die is cut.
Can you work from a 3D file instead of a physical sample?
Yes. A STEP file with ports, buttons and antenna zones marked is enough. If you only have a drawing, we cut a 1:1 mock-up in 25D EVA and check it against the device first.
How thick should the foam be?
10–30 mm inside a 5 mm shell. A 20 mm insert holds a camera or a handset; a 30 mm insert fills a tool case. The shell depth and the device height set the ceiling.
Do inserts add to the case price?
Yes. A pick-and-pluck insert adds roughly US$0.40–0.80 per piece at 1,000 pcs; a die-cut 38D insert adds US$0.90–1.60 plus the one-off die, which stays on file for reorders.

Send the device, get a cavity drawing

A STEP file, a 1:1 mock-up or the unit itself is enough to start. We reply with an insert type, a tolerance and a price.