Private Label Hard Cases With Your Own Branding

You sell the case under your brand, so every surface has to carry it: the moulded shell, the zipper puller, the lining, the woven label, the retail box and the shipping carton. We produce 300 pcs per style with your mark embossed, heat-transferred, plated or patched, matched to a Pantone reference and packed for retail or Amazon FBA.

Your brand

Your logo in the material, not on a sticker

Embossing is the method most brands settle on: a brass die presses your mark into the 1680D face while the shell is still warm, so the logo sits in the material and cannot peel off in a warehouse. Heat transfer suits fine lettering and one or two spot colours. A metal plate or a rubber patch signals a heavier, hardware-led product. Every die is cut from your artwork.

Brand consistency is a colour problem more than a logo problem. We match the face fabric, the velvet lining, the zipper tape and the webbing handle to one Pantone reference, then keep that reference on file so a reorder next season does not drift. Colour is checked under D65 light before the sample ships, never by eye on a phone screen.

  • Logo methods: embossed, heat transfer, metal plate, rubber patch
  • Pantone-matched face fabric, lining and zipper tape
  • Woven main label, printed care label and zipper puller
  • Retail box, barcode and Amazon-ready shipping carton
Send Your Design
Embossed logo being pressed into the fabric face of an EVA case
Decisions

Three choices decide how the case reads

Two brands can order the same shell and end up with products that look nothing alike. These are the three settings that separate them.

The logo method

Embossed into the face fabric, heat transferred, riveted as a metal plate or stitched as a rubber patch. Each method changes the tooling cost and the minimum quantity, so we quote all four.

The colour match

Face fabric, velvet lining, zipper tape and webbing handle are matched to one Pantone reference and checked under D65 light before the sample leaves the factory.

The pack-out

Printed retail box, insert card, hangtag, barcode and carton mark. We print the box and apply the barcode in the same building as the final inspection.

Brand control

What comes back to you, and what stays on file

Before a full run we build a branded pre-production sample with your final die, label, puller and box, then photograph it under D65 light beside your Pantone chip. That sample becomes the standard: shell colour, stitch colour, label position and carton print stay fixed for the whole order and for the reorder after it. It stays in our sample room with your brand file.

Every carton passes a label audit: logo placement checked against the approved template, zipper pullers counted, hangtag and barcode scanned, and the retail box closed to your pack-out sheet. Anything that fails goes back to the packing table before the carton is sealed, marked and added to the packing list. The audit is photographed, so a buyer can see the carton that shipped.

  • Branded PP sample photographed beside your Pantone chip
  • Label, puller and hangtag counted per carton
  • Barcode scanned and confirmed before sealing
  • Artwork, dies and colour references held for reorders
Ask for a mock-up
Label and logo audit on a private label EVA case before packing
Projects

Private label cases we have branded

Same mould library, different brand kits. Each of these can run at 300 pcs with your own die, lining colour and box.

Process

Five steps from a logo file to a retail carton

A stock mould keeps this short. Branding work runs in parallel with moulding, so the logo never holds the shell.

01

Send the brand kit

Logo in AI or PDF, Pantone references, label wording, barcode number and any packaging you already use. A competitor case helps us read the target.

02

Mock-up on a stock mould

We place your logo on a case from the 300+ library in two or three methods and send photos with the tooling cost for each, usually within two working days.

03

Branded sample

7–10 days with your die, label, puller, lining colour and box, photographed under D65 light next to the Pantone chip it was matched to, then couriered to you.

04

Production and pack-out

20–30 days of moulding and stitching, then labels, barcodes and retail boxes applied at the packing table under the same roof and checked against your pack-out sheet.

05

Audit and ship

A photo report of the finished cartons, the barcode scanned and confirmed against your number, then FOB, CIF or DDP delivery to your warehouse or to Amazon.

Specs

Private label specification range

The branding variables we hold in-house, from the die to the carton mark.

Material
5 mm EVA foam, 75D, faced in 1680D nylon, 600D polyester or PU leather
Shell
Compression moulded in your chosen shape, 300+ moulds in the library
Lining
Velvet, jersey or plain EVA, matched to a Pantone reference
Zipper
YKK or waterproof, with a custom puller and your logo
Logo
Embossed, heat transfer, metal plate, rubber patch or silk screen
Labels
Woven main label, printed care label, size tab, hangtag
Packaging
Printed retail box, insert card, barcode, FBA-ready carton
MOQ
300 pcs per style, 100 pcs per colour on stock moulds
Lead time
7–10 days branded sampling; 20–30 days bulk production
Pricing

Indicative private label pricing

FOB Shenzhen at 1,000 pcs, with your logo applied, your lining colour and a printed retail box. Price moves with case size and how much of the pack-out you hand us.

Small cases

US$3.10 / pc

Watch and jewellery formats at 1,000 pcs, logo and retail box included.

  • 300 pcs MOQ
  • One embossed logo die, cut to your artwork
  • Woven label and printed hangtag
  • Printed retail box and barcode

Large cases

US$10.50 / pc

Drone, VR headset and keyboard formats at 2,000 pcs.

  • 2,000 pcs per style
  • Rubber patch or metal plate
  • Printed sleeve and insert card
  • FBA carton marks and label spec

Questions private label buyers ask

Can you brand a case that already exists in your range?
Yes. Pick a mould from the 300+ library, then choose the logo method, lining colour, puller and box. Sampling takes 7–10 days because no new shell tooling is needed.
What is the minimum order for private label cases?
300 pcs per style, 100 pcs per colour on a stock mould. A logo die, woven label and printed box all run at that quantity without a surcharge.
Can you match my Pantone colour?
We match face fabric, lining, zipper tape and webbing to one Pantone reference, then check the result under D65 light before the sample ships.
Do you pack for Amazon FBA?
Yes: FNSKU labels, polybag warnings, a barcode verified with a scanner, and cartons weighed and marked to the FBA spec. We can also print the retail box and insert card.
How long does a private label order take?
A branded sample in 7–10 days on a stock mould, then 20–30 days of production, then freight. Packaging print runs in parallel with the cases, not after them.

Put your name on 300 cases

Send your logo and the Pantone references you care about. We will return a mock-up on a stock mould, a costed pack-out and a sampling date.